Page 182 - MEMS Mechanical Sensors

7.9 Future Devices 171

[48] Ebi, G., et al., “Integrated Optical Noncontact Torque Measurement Microsystem,” Opt.
Eng., Vol. 38, No. 2, 1999, pp. 240–245.
[49] Meckes, A., et al., “Capacitive Silicon Microsensor for Force and Torque Measurement,”
Proc. TRANSDUCERS ’01 – Eurosensors XV , Munich, Germany, June 10–14, 2001,
pp. 498–501.
[50] Cermak, S., et al., “Capacitive Sensor for Torque Measurement,” Proc. Intl. Measurement
Confederation XVI IMEKO World Congress, Vol. III, Vienna, Austria, September 25–28,
2000, pp. 25–28.
[51] Turner, J. D., and L. Austin, “Sensors for Automotive Telematics,” Measurement Science
and Technology, Vol. 11, No. 2, 2000, pp. R58–R79.
[52] Despont, M., et al., “New Design of Micromachined Capacitive Force Sensor,” J. Micro-
mech. Microeng., Vol. 3, No. 4, 1993, pp. 239–242.
[53] Wiegerink, R., et al., “Quasi-Monolithic Silicon Load Cell for Loads Up to 1000 kg with
Insensitivity to Non-Homogeneous Load Distributions,” Proc. 12th IEEE Intl. Conf.
Micro Electro Mechanical Systems, Orlando, FL, January 17–21, 1999, pp. 558–563.
[54] Enikov, E. T., and B. J. Nelson, “Three-Dimensional Microfabrication for a Multi-Degree-
of-Freedom Capacitive Force Sensor Using Fiber-Chip Coupling,” J. Micromech. Micro-
eng., Vol. 10, No. 4, 2000, pp. 492–497.
[55] Sasada, I., S. Uramoto, and K. Harada, “Noncontact Torque Sensors Using Magnetic
Heads and a Magnetostrictive Layer on the Shaft Surface-Application of Plasma Jet Spray-
ing Process,” IEEE Trans. on Magnetics, Vol. 22, No. 5, 1986, pp. 406–408.
[56] Rombach, P., H. Steiger, and W. Langheinrich, “Planar Coils with Ferromagnetic Yoke for
a Micromachined Torque Sensor,” J. Micromech. Microeng., Vol. 5, No. 2, 1995,
pp. 136–138.
[57] Rombach, P., and W. Langheinrich, “Modeling of a Micromachined Torque Sensor,” Sen-
sors and Actuators, Vol. A46, No. 1–3, 1995, pp. 294–297.
[58] Romback, P., and W. Langheinrich, “An Integrated Sensor Head in Silicon for Contactless
Detection of Torque and Force,” Sensors and Actuators, Vol. A42, No. 1–3, 1994,
pp. 410–416.
[59] Sahashi, M., et al., “A New Contact Amorphous Torque Sensor with Wide Dynamic
Range and Quick Response,” IEEE Trans. on Magnetics, Vol. 23, No. 5, 1987,
pp. 2194–2196.
[60] Umbach, F., et al., “Contactless Measurement of Torque,” Mechatronics, Vol. 12, No. 8,
2002, pp. 1023–1033.
[61] Brugger, J., et al., “Microfabricated Ultrasensitive Piezeoresistive Cantilevers for Torque
Magnetometry,” Sensors and Actuators, Vol. 73, No. 3, 1999, pp. 235–242.
[62] Lee, C., et al., “Characterization of Micromachined Piezoelectric PZT Force Sensors for
Dynamic Scanning Force Microscopy,” Rev. Sci. Instrum., Vol. 68, No. 5, 1997,
pp. 2091–2099.
[63] Brook, A. J., et al., “Micromachined III-V Cantilevers for AFM-Tracking Scanning Hall
Probe Microscopy,” J. Micromech. Microeng., Vol. 13, No. 1, 2003, pp. 124–128.
[64] Lee, D. W., et al., “Switchable Cantilever Fabrication for a Novel Time-of-Flight Scanning
Force Microscope,” Microelectric Engineering, Vol. 67–68, 2003, pp. 635–643.
[65] Drews, D., et al., “Micromachined Aperture Probe for Combined Atomic Force and Near-
Field Scanning Optical Microscopy (AFM/NSOM),” Proc. Conf. on Materials and Device
Characterization in Micromachining, Santa Clara, CA, September 21–22, 1998, SPIE, Vol.
3512, 1998, pp. 76–83.
[66] Abraham, M., et al., “Micromachined Aperture Probe Tip for Multifunctional Scanning
Probe Microscopy,” Utramicroscopy, Vol. 71, No. 1–4, 1998, pp. 93–98.
[67] Greitmann, G., and R. A. Buser, “Tactile Microgripper for Automated Handling of Micro-
parts,” Sensors and Actuators, Vol. A53, No. 1–3, 1996, pp. 410–415.