Page 245 - 3D Fibre Reinforced Polymer Composites

234 References

Tan P., L. Tong and G.P. Steven, 1997b, A three-dimensional modelling technique for
predicting the linear elastic properties of open-packing woven fabric unit cell,
Comp. Struct., 38:261-271.
Tan P., L. Tong and G.P. Steven, 1998, Modelling approaches for 3D orthogonal woven
composites, J. Rein. Plastics & Comp., 17545-577.
Tan P., L. Tong and G.P. Steven, 1999a, Models for predicting thermomechanical
properties of 3D orthogonal woven composites, J. Rein. Plastics & Comp., 18: 15 1.
Tan P., L. Tong and G.P. Steven, 1999b, Micro-mechanics models for mechanical and
thermo-mechanical properties of 3D angle interlock woven composites, Comp.,
30Az637-648.
Tan P., L. Tong, G.P. Steven and T. Ishikawa. 2000a. Behaviour of 3D orthogonal
woven CFRP composites. I: Experimental investigation, Composites, 3 1A:259-27 1.
Tan P., L. Tong and G.P. Steven, 2000b, Behaviour of 3D orthogonal woven CFRP
composites. 11: Theoretical and FEA modelling, Composites, 3 1A:273-28 1.
Tan P., L. Tong and G.P. Steven, 2001, Mechanical behaviour for 3-D orthogonal
woven E-glass/epoxy composites, J. Rein. Plastics & Comp., 20:274-303.
Tanzawa Y., N. Watanabe and T. Ishikawa, 1997, Interlaminar delamination toughness
and strength of 3-D orthogonal interlocked fabric composite, Roc. of the Eleventh
Int. Conf. on Composite Materials, Ed. M.L. Scott, 14-18 July, Gold Coast,
Australia, V-47 to V-57.
Tarnopol'skii Y.M., V.A. Polyakor and L.G. Zhigun, 1973, Composite materials
reinforced with a system of three mutually orthogonal fibres, I: Calculation of elastic
characteristics, Polymer Mechanics, 5:853-860.
Thaxton C., R. Reid and A. El-Shiekh, 1991, Advances in 3-dimensional braiding, Proc.
of the 5th Conf. on Advanced Engineering Fibres and Textile Structures for
Composites"", NASA Conf. Publication 3 176,43-66.
Thompson D.M. and O.H. Griffin, 1990,2-D to 3-D globalllocal finite element analysis
of cross-ply composite laminates, J. Rein. Plastics & Comp. 9:492-502.
Thompson D.M. and O.H. Griffin, 1992, Verification of a 2-D to 3-D globalllocal finite
element method for symmetric laminates, J. Rein. Plastics & Comp., 11:910-931.
Thuis H.G.S.J. and E. Bron, 1996, The effect of stitching density and laminate lay-up on
the mechanical properties of stitched carbon fabrics, National Lucht-en
Ruimtevaartlaboratorium, Report NLR CR 96126L.
Tong L. and L.K. Jain, 1995, Analysis of adhesive bonded composite lap joints with
transverse stitching, App. Comp. Mat., 2:343.
Tong L, J.K. Jain, K.H. Leong, D. Kelly and I. Hertzberg, 1998a, Failure of transversely
stitched RTM lap joints, Comp. Sci. & Tech., 58:221-227.
Tong L, K. Cleaves, T. Kruckenberg and G.P. Steven, 1998b, Effect of transverse
stitching on the fracture loads of RTM single lap joints, Key Eng. Mat., 137:195.
Tong L., P. Tan and G.P. Steven, 2002, Effect of yarn waviness on strength of 3D
orthogonal woven CFRP composite materials, J. Rein. Plastics & Comp., 21: 153.
Tsai S.W. and E.M. Wu, 1971, A general theory of strength for anisotropic materials, J.
Comp. Mat., 558-80.
Turrettini A., 1996, An investigation of the mode I and I1 stitch bridging laws in
stitched polymer composites, Masters Thesis, Department of Mechanical &
Environmental Engineering, University of California, Santa Barbara.