Page 220 - MEMS Mechanical Sensors
P. 220
8.4 Future Inertial Micromachined Sensors 209
[28] Ward, M. C. L., D. O. King, and A. M. Hodge, “Performance Limitations of Surface-
Machined Accelerometers Fabricated in Polysilicon Gate Material,” Sensors and Actuators,
Vol. A46–47, 1995, pp. 205–209.
[29] Kuehnel, W., and S. Sherman, “A Surface Micromachined Silicon Accelerometer with On-
Chip Detection Circuitry,” Sensors and Actuators, Vol. A45, 1994, pp. 7–16.
[30] Chau, K., et al., “An Integrated Force Balanced Capacitive Accelerometer for Low-g Appli-
cations,” Sensors and Actuators, Vol. A54, 1996, pp. 472–476.
[31] Lu, C., M. Lemkin, and B. Boser, “A Monolithic Surface Micromachined Accelerometer
with Digital Output,” IEEE J. Solid-State Circuits, Vol. 30, No. 12, 1995, pp. 1367–1373.
[32] Boser, B. E., and R. T. Howe, “Surface Micromachined Accelerometers,” IEEE J. of Solid-
State Circuits, Vol. 31, No. 3, 1996, pp. 336–375.
[33] Yazdi, N., and K. Najafi, “An All-Silicon Single-Wafer Micro-g Accelerometer with a Com-
bined Surface and Bulk Micromachining Process,” J. of Micromech. Microeng., Vol. 9,
No.4, 2000, pp. 544–550.
[34] Chen, P. L., R. S. Muller, and A. P. Andrews, “Integrated Silicon Pi-FET Accelerometers
with Proof Mass,” Sensors and Actuators, Vol. 5, No.2, 1983, pp. 119–126.
[35] Nemirovsky, Y., et al., “Design of a Novel Thin-Film Piezoelectric Accelerometer,” Sensors
and Actuators, Vol. A56, 1996, pp. 239–249.
[36] Beeby, S. P., N. J. Grabham, and N. M. White, “Microprocessor Implemented Self-
Validation of Thick-Film PZT/Silicon Accelerometer,” Sensors and Actuators, A92, 2001,
pp. 168–174.
[37] Rockstad, H. K., et al., “A Miniature, High-Sensitivity, Electron Tunnelling Accelerome-
ter,” Sensors and Actuators, Vol. A53, 1996, pp. 227–231.
[38] Burns, D. W., et al., “Sealed-Cavity Resonant Microbeam Accelerometer,” Sensors and
Actuators, Vol. A53, 1996, pp. 249–255.
[39] Roessig, T. A., et al., “Surface-Micromachined Resonant Accelerometer,” 9th Int. Conf.
Solid-State Sensors and Actuators (Transducer ’97), Chicago, IL, 1997, pp. 859–862.
[40] Roszhart, T. V., et al., “An Inertial Grade, Micromachined Vibrating Beam Accelerome-
ter,” 8th Intl. Conf. Solid-State Sensors and Actuators (Transducer ’95), Stockholm, Swe-
den, 1995, pp. 659–662.
[41] Burrer, C., J. Esteve, and E. Lora-Tomayo, “Resonant Silicon Accelerometer in Bulk-
Micromachining Technology,” J. of Micromech. Microeng., Vol. 5, No. 2, 1996, pp.
122–130.
[42] Lemkin, M. A., et al., “A Three-Axis Force Balanced Accelerometer Using a Single Proof
Mass,” 9th Intl. Conf. Solid-State Sensors and Actuators (Transducer ’97), Chicago, IL,
1997, pp. 1185–1188.
[43] Lemkin, M. A., and B. Boser, “A Three-Axis Micromachined Accelerometer with a CMOS
Position-Sense Interface and Digital Offset-Trim Electronics,” IEEE J. of Solid-State Cir-
cuits, Vol. 34, No. 4, 1999, pp. 456–468.
[44] Mineta, T., et al., “Three-Axis Capacitive Accelerometer with Uniform Axial Sensitivities,”
J. of Micromech. Microeng., Vol. 6, 1996, pp. 431–435.
[45] Takao, H., Y. Matsumoto, and M. Ishida, “A Monolithically Integrated Three-Axis Accel-
erometer Using CMOS Compatible Stress-Sensitive Differential Amplifiers,” IEEE Trans.
on Electron Devices, Vol. 46, No. 1, 1999, pp. 109–116.
[46] Takao, H., Y. Matsumoto, and M. Ishida, “Stress-Sensitive Differential Amplifiers Using
Piezoresistive Effects of MOSFETs and Their Application to Three-Axial Accelerometers,”
Sensors and Actuators, Vol. A65, 1998, pp. 61–68.
[47] Schröpfer, G., et al., “Lateral Optical Accelerometer Micromachined in (100) Silicon with
Remote Readout Based on Coherence Modulation,” Sensors and Actuators, Vol. A68,
1998, pp. 344–349.
[48] Huang, R. S., E. Abbaspour-Sani, and C. Y. Kwok, “A Novel Accelerometer Using Silicon
Micromachined Cantilever Supported Optical Grid and PIN Photodetector,” 8th Intl.